DasCamel's 375 DT build. What could go wrong? - Page 4

DasCamel · 01/11/2017, 12:25 PM

Transfer subjects. Excited about a larger home.

Sent from my SM-G935T using Tapatalk

DasCamel · 01/11/2017, 12:29 PM

So the salinity is going to be spot on match after a little more water is added.

Bigger issue is the temp. I'm at 74.5 with a couple heaters. Heating that huge mass of water is slow. House temp is about 71.

So, no half measures.

So I added more heaters... Terminator approves of the extra energy after photo bombing.

Sent from my SM-G935T using Tapatalk

roli112 · 01/11/2017, 12:46 PM

Ill be back

worm5406 · 01/11/2017, 12:52 PM

How are the lights looking?

DasCamel · 01/11/2017, 12:56 PM

The lights were a PITA. Found an air duct above a mount point. So, added a 2×4 across for now to bypass it. About to plug them in, need another circuit though. With all the heaters prolly trip a breaker...

Sent from my SM-G935T using Tapatalk

DasCamel · 01/11/2017, 01:02 PM

Success temp raised by .2 degrees. Yes, .2 in about an hour... time to use another heater from the breeder lol.

Sent from my SM-G935T using Tapatalk

worm5406 · 01/11/2017, 01:05 PM

Very nice. Turn them lights on and see if they help heat it up too.

DasCamel · 01/11/2017, 02:12 PM

Going need a nuclear reactor soon. Soooo, I just added another gfci to another circuit in the basement. Factoring the bathroom that's three 15 amp circuits to split the load of everything to, plus standard usage down here. Anyway, to the displeasure of my neck and back. Lights soon, hope they work lol. Haven't touched them since a test early November

Sent from my SM-G935T using Tapatalk

roli112 · 01/11/2017, 03:10 PM

should have boiled some of that RODI water

DasCamel · 01/11/2017, 04:39 PM

Quote:

Originally Posted by roli112

should have boiled some of that RODI water

Good idea for later! Temp is up to 76... It'll get there, eventually.

Made a makeshift power panel mounting board and we have light. Well, one for now lol. Using an Apex energy Bar w/o the Apex setup.

Also, first casualty. So figured out a solution to the neck and back issues.

Get another body part to hurt more. Crushed my nail bed right in half. Remember that ice cold tap water. Savior! Plus, pain meds... Good time for a break lol. Need to recruit the family to finish up for the day.

Sent from my SM-G935T using Tapatalk

DasCamel · 01/11/2017, 07:30 PM

And more lights. Haven't hooked up the controller yet. Lights are default 80%. I'll worry about the T5s in a month or two.

Sent from my SM-G935T using Tapatalk

DasCamel · 01/11/2017, 07:31 PM

Quote:

Originally Posted by DasCamel

And more lights. Haven't hooked up the controller yet. Lights are default 80%. I'll worry about the T5s in a month or two.

Sent from my SM-G935T using Tapatalk

worm5406 · 01/11/2017, 11:39 PM

Wait I do not see the RO line. Where did it go?

DasCamel · 01/11/2017, 11:45 PM

I fired up the return and ran out of water in the sump.

Oops, need to add more water lol. I need to calculate heating wattage. I think adding chilled RO/DI is combating my efforts. Thermodynamics for the win!

Sent from my SM-G935T using Tapatalk

worm5406 · 01/12/2017, 12:08 AM

Ohh yes, I agree.

100g of 100 degree water and mix in 100g of 70 degree water and you will get 85 degree water. Temperature goes to cold quicker.

Just saying.

McPuff · 01/12/2017, 07:18 AM

Quote:

Originally Posted by DasCamel

I already have everything cycled. Zero sand. Everthing in good condition. Still going to acclimate just because IO vs Reef Crystal's.
The live rock from the other tank, zero die off equals zero cycle... Yes. I'm that crazy. Well not really, already moved everything 1000 miles in a cooler... Theory is sound.

Sent from my SM-G935T using Tapatalk

That's awesome. I wasn't worried about a cycle at all... just acclimation. Sounds like you've got a good plan. Have you finished yet?!?! :0)

DasCamel · 01/12/2017, 01:07 PM

Close, everything little snowballs into 3 more things.

Lights good now, temp and salinity are a close match. Return pump is up and running. Going to start acclimation this afternoon.

Sent from my SM-G935T using Tapatalk

ADVRESOURCE · 01/12/2017, 01:31 PM

Is rock close to surface?

DasCamel · 01/12/2017, 03:58 PM

Quote:

Originally Posted by ADVRESOURCE

Is rock close to surface?

One rock is just few inches under on the right side.

Sent from my SM-G935T using Tapatalk

DasCamel · 01/12/2017, 04:24 PM

Ok, transfering...

Sent from my SM-G935T using Tapatalk

DasCamel · 01/13/2017, 12:33 AM

Adding the fish really helped put a perspective to size. Time to start buying and quarantining fish.

Thinking of couple of skunk clowns for haddoni, and a pair of yellow tangs.

Going to hold off a bit on corals until I get the top off, skimmer, Apex and such setup.

The T5 lights will also help balance out the light. On the photos, the phone camera is really picking up the higher rocks. Eventually, want to get Mags and Gigs up there.

Need a solution for the haddoni, got him in a glass bowl of sand. Maybe make him a permanent acrylic sandbox.

So far, so good.

DasCamel · 01/21/2017, 11:32 PM

So have a pair of cute orange skunk clowns in the QT along with a royal gramma. Starting simple and slow. Next fish batch in Feb, thinking of the yellow tangs. Odd number seems to be preferred, so 3 it is.

So figured out the right height for the skimmer. 3D printing a stand for it. Had some spare filament around, HIPS. Let's see how the design works.

DasCamel · 01/22/2017, 10:44 PM

Tunze ozmolator hooked up. Gotta say, it does make life easy. Going to buy a 55g petco tank and use that as the ATO resovior. $1 a gallon FTW. It fits underneath the stand, in the other half with room to spare. Safe to say, all the space will eventually be used.

Here's the 3D printed stand.

7 x 7 x 7.5, can't believe I haven't printed tank parts sooner.

Next up, custom probe and heater holders. I can keep them stable and the heater top out of the water.

roli112 · 01/23/2017, 06:56 PM

How hard is it to design stuff to print? I'm starting to get curious but have no experience with that kind of stuff

DasCamel · 01/23/2017, 11:40 PM

Quote:

Originally Posted by roli112

How hard is it to design stuff to print? I'm starting to get curious but have no experience with that kind of stuff

Super easy. Check out Tinkercad, free and web based.

I'm using a Taz 5 from Lulzbot to print. All open source. Can even 3D print to upgrade itself.

01/11/2017, 12:25 PM	#76
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Transfer subjects. Excited about a larger home. Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 12:29 PM	#77
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	So the salinity is going to be spot on match after a little more water is added. Bigger issue is the temp. I'm at 74.5 with a couple heaters. Heating that huge mass of water is slow. House temp is about 71. So, no half measures. So I added more heaters... Terminator approves of the extra energy after photo bombing. Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 12:46 PM	#78
roli112 Registered Member Join Date: Apr 2011 Location: Los Angeles Posts: 298	Ill be back __________________ 180 gallon mixed reef Current Tank Info: 180g. mix reef

01/11/2017, 12:52 PM	#79
worm5406 Not afriad to admit wrong Join Date: Jun 2012 Location: South of WashDC in Maryland Posts: 7,774	How are the lights looking? __________________ Stock:LPS/SPS\|1 hippo\|4 OC Clown\|4 Pepp shrimp\|2 Brittle Star\|3000+ Copepods\|10+ MiniBrittle\|8+ Bristle Worm\|2 Anemone\|100+ mini-feather\|4 boys 14,21,22,22 Current Tank Info: Tank:300g Mixed Reef 300+lb LR\|4" LS\|5x MP40W\|75g fuge\|5x RadionPRO\|RO DB250 skimmer\|Apex

01/11/2017, 12:56 PM	#80
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	The lights were a PITA. Found an air duct above a mount point. So, added a 2×4 across for now to bypass it. About to plug them in, need another circuit though. With all the heaters prolly trip a breaker... Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 01:02 PM	#81
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Success temp raised by .2 degrees. Yes, .2 in about an hour... time to use another heater from the breeder lol. Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 01:05 PM	#82
worm5406 Not afriad to admit wrong Join Date: Jun 2012 Location: South of WashDC in Maryland Posts: 7,774	Very nice. Turn them lights on and see if they help heat it up too. __________________ Stock:LPS/SPS\|1 hippo\|4 OC Clown\|4 Pepp shrimp\|2 Brittle Star\|3000+ Copepods\|10+ MiniBrittle\|8+ Bristle Worm\|2 Anemone\|100+ mini-feather\|4 boys 14,21,22,22 Current Tank Info: Tank:300g Mixed Reef 300+lb LR\|4" LS\|5x MP40W\|75g fuge\|5x RadionPRO\|RO DB250 skimmer\|Apex

01/11/2017, 02:12 PM	#83
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Going need a nuclear reactor soon. Soooo, I just added another gfci to another circuit in the basement. Factoring the bathroom that's three 15 amp circuits to split the load of everything to, plus standard usage down here. Anyway, to the displeasure of my neck and back. Lights soon, hope they work lol. Haven't touched them since a test early November Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 03:10 PM	#84
roli112 Registered Member Join Date: Apr 2011 Location: Los Angeles Posts: 298	should have boiled some of that RODI water __________________ 180 gallon mixed reef Current Tank Info: 180g. mix reef

01/11/2017, 07:30 PM	#86
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	And more lights. Haven't hooked up the controller yet. Lights are default 80%. I'll worry about the T5s in a month or two. Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/11/2017, 11:39 PM	#88
worm5406 Not afriad to admit wrong Join Date: Jun 2012 Location: South of WashDC in Maryland Posts: 7,774	Wait I do not see the RO line. Where did it go? __________________ Stock:LPS/SPS\|1 hippo\|4 OC Clown\|4 Pepp shrimp\|2 Brittle Star\|3000+ Copepods\|10+ MiniBrittle\|8+ Bristle Worm\|2 Anemone\|100+ mini-feather\|4 boys 14,21,22,22 Current Tank Info: Tank:300g Mixed Reef 300+lb LR\|4" LS\|5x MP40W\|75g fuge\|5x RadionPRO\|RO DB250 skimmer\|Apex

01/11/2017, 11:45 PM	#89
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	I fired up the return and ran out of water in the sump. Oops, need to add more water lol. I need to calculate heating wattage. I think adding chilled RO/DI is combating my efforts. Thermodynamics for the win! Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/12/2017, 12:08 AM	#90
worm5406 Not afriad to admit wrong Join Date: Jun 2012 Location: South of WashDC in Maryland Posts: 7,774	Ohh yes, I agree. 100g of 100 degree water and mix in 100g of 70 degree water and you will get 85 degree water. Temperature goes to cold quicker. Just saying. __________________ Stock:LPS/SPS\|1 hippo\|4 OC Clown\|4 Pepp shrimp\|2 Brittle Star\|3000+ Copepods\|10+ MiniBrittle\|8+ Bristle Worm\|2 Anemone\|100+ mini-feather\|4 boys 14,21,22,22 Current Tank Info: Tank:300g Mixed Reef 300+lb LR\|4" LS\|5x MP40W\|75g fuge\|5x RadionPRO\|RO DB250 skimmer\|Apex

01/12/2017, 01:07 PM	#92
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Close, everything little snowballs into 3 more things. Lights good now, temp and salinity are a close match. Return pump is up and running. Going to start acclimation this afternoon. Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/12/2017, 01:31 PM	#93
ADVRESOURCE Registered Member Join Date: Aug 2006 Location: TUCSON Posts: 569	Is rock close to surface?

01/12/2017, 04:24 PM	#95
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Ok, transfering... Sent from my SM-G935T using Tapatalk __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/13/2017, 12:33 AM	#96
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Adding the fish really helped put a perspective to size. Time to start buying and quarantining fish. Thinking of couple of skunk clowns for haddoni, and a pair of yellow tangs. Going to hold off a bit on corals until I get the top off, skimmer, Apex and such setup. The T5 lights will also help balance out the light. On the photos, the phone camera is really picking up the higher rocks. Eventually, want to get Mags and Gigs up there. Need a solution for the haddoni, got him in a glass bowl of sand. Maybe make him a permanent acrylic sandbox. So far, so good. __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/21/2017, 11:32 PM	#97
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	So have a pair of cute orange skunk clowns in the QT along with a royal gramma. Starting simple and slow. Next fish batch in Feb, thinking of the yellow tangs. Odd number seems to be preferred, so 3 it is. So figured out the right height for the skimmer. 3D printing a stand for it. Had some spare filament around, HIPS. Let's see how the design works. __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197

01/22/2017, 10:44 PM	#98
DasCamel Registered Member Join Date: Oct 2013 Location: Kenmore, WA Posts: 1,542	Tunze ozmolator hooked up. Gotta say, it does make life easy. Going to buy a 55g petco tank and use that as the ATO resovior. $1 a gallon FTW. It fits underneath the stand, in the other half with room to spare. Safe to say, all the space will eventually be used. Here's the 3D printed stand. 7 x 7 x 7.5, can't believe I haven't printed tank parts sooner. Next up, custom probe and heater holders. I can keep them stable and the heater top out of the water. __________________ 375g DT 125g sump acrylic, Mixed SPS/LPS tank with anemones and fish. Current Tank Info: 375g Build thread http://www.reefcentral.com/forums/showthread.php?t=2608197 Last edited by DasCamel; 01/22/2017 at 10:53 PM.

01/23/2017, 06:56 PM	#99
roli112 Registered Member Join Date: Apr 2011 Location: Los Angeles Posts: 298	How hard is it to design stuff to print? I'm starting to get curious but have no experience with that kind of stuff __________________ 180 gallon mixed reef Current Tank Info: 180g. mix reef