Reef Central Online Community

ProfiLux Remote Access

Posted 05/16/2011 at 04:45 PM by snorvich (System configuration and fish for my two tanks)
Updated 05/19/2011 at 02:11 PM by snorvich

Tags profilux

Quote:

Originally Posted by Pro_Reef

Setting up your Profilux for remote log in isn't "too" complicated, but does require a little familiarity with your router.

First off you need to determine what the IP address of your profilux is. The simplest way to do this is to manually configure your Profilux with a static IP address. In the Profilux Software you do this as follows:

1.) connect to your Profilux using the Profilux Control Software
2.) Click on the "System" section of

...

snorvich

Team RC member

Posted in Profilux

Views 33546 Comments 0

GHL Dosing

Posted 05/07/2011 at 01:36 PM by snorvich (System configuration and fish for my two tanks)
Updated 05/19/2011 at 02:12 PM by snorvich

Tags profilux

Ok here we go the rest of the guide

So before we can even start talking about setting up dose rates and anything else we need to program the doser. (if you are reading this on the FM forum, I hope this info helps you also)

For slave dosers with the profiLux

This is where the profiLux shines above all other controllers, as you know GHL make a slave doser that works in unison with the controller, this gives the unique feature that you can dose in controlled...

snorvich

Team RC member

Posted in Profilux

Views 24610 Comments 0

Profilux control of Tunze

Posted 05/04/2011 at 06:12 PM by snorvich (System configuration and fish for my two tanks)
Updated 05/19/2011 at 02:13 PM by snorvich

Tags profilux

Quote:

Originally Posted by chem-e

I'm using two Tunze 6055 and an MP40 on my tank, but I use sequence 1 with 30% min to 80% max, off at night (only MP40 on night mode does the job), and 80% for storms (not that I use it).

Here's the info I got off the manual and I think this is one of the few sections that I find useful.

Hopefully, this is helpful.

6.5.2.1 Operational mode
Off – the pumps of this group are permanently off.
Permanent – the pumps are permanently active and

...

snorvich

Team RC member

Posted in Profilux

Views 23659 Comments 0

Requesting help with PAB

Posted 04/27/2011 at 07:09 PM by snorvich (System configuration and fish for my two tanks)
Updated 05/19/2011 at 02:14 PM by snorvich

Tags profilux

IF you have PAB power bars they do not plug into S1S4, they plug into PAB ports. On the back of your profilux you have two PAB ports and on the power bar there is a PAB port, the cable (RJ45 which is standard cat5e cable) plugs into this.

From the very first part of the manual
http://support.aquariumcomputer.com/...n_PAB_V500.pdf

"1 Connection
Devices with ProfiLux Aquatic Bus – in short PAB – are connected to the corresponding RJ45...

snorvich

Team RC member

Posted in Profilux

Views 21673 Comments 0

Assistance with wireless connection of P3e

Posted 04/27/2011 at 07:06 PM by snorvich (System configuration and fish for my two tanks)
Updated 05/19/2011 at 02:15 PM by snorvich

Tags profilux

Quote:

Originally Posted by tonyf

Me again.

So now I have consumed my entire Sunday morning attempting to coax the P3e to connect wirelessly to PLC 5.0.4.2. I am not kidding when I tell you that I have been through the process 10 times, repeating it slavishly as set out in GHL’s instructions (W)LAN instructions and Boboxx’s notes in his post above.

Just to run through the network hardware again:
(1) Wireless router – Netgear N300 Model WNR200v2
(2) Wireless adaptor – Netgear Universal

...

snorvich

Team RC member

Posted in Profilux

Views 21639 Comments 0

Total Blogs	145
Total Entries	773
Entries in Last 24 Hours	0

Archive
< November 2024
Su	Mo	Tu	We	Th	Fr	Sa
20	21	22	23	24	25	26
27	28	29	30	31	1	2
3	4	5	6	7	8	9
10	11	12	13	14	15	16
17	18	19	20	21	22	23
24	25	26	27	28	29	30

vBulletin Message

Cancel Changes